Struct SignalProcessingProxy

pub struct SignalProcessingProxy { /* private fields */ }

Implementations

impl SignalProcessingProxy

pub fn new(channel: AsyncChannel) -> Self

Create a new Proxy for fuchsia.hardware.audio.signalprocessing/SignalProcessing.

pub fn take_event_stream(&self) -> SignalProcessingEventStream

Get a Stream of events from the remote end of the protocol.

Panics

Panics if the event stream was already taken.

pub fn get_elements( &self, ) -> QueryResponseFut<ReaderGetElementsResult, DefaultFuchsiaResourceDialect>

Returns a vector of supported processing elements. Must return one or more processing elements, or ZX_ERR_NOT_SUPPORTED. If GetTopologies returns one or more topologies, then GetElements must return one or more elements.

pub fn watch_element_state( &self, processing_element_id: u64, ) -> QueryResponseFut<ElementState, DefaultFuchsiaResourceDialect>

Get the processing element state via a hanging get. For a given processing_element_id, the driver will reply to the first WatchElementState sent by the client. The driver will not respond to subsequent client WatchElementState calls for a given processing_element_id until any field of the Element table changes from what was most recently reported for that processing_element_id.

The driver will close the protocol channel with an error of ZX_ERR_BAD_STATE, if this method is called again while there is already a pending WatchElementState for this client and processing_element_id.

pub fn get_topologies( &self, ) -> QueryResponseFut<ReaderGetTopologiesResult, DefaultFuchsiaResourceDialect>

Returns a vector of supported topologies. Must return one or more topologies, or ZX_ERR_NOT_SUPPORTED. If more than one topology is returned, then the client may choose any of the topologies from the list with SetTopology. If only one topology is returned, then the topology definition is informational only since the one and only topology used can’t be changed with SetTopology. If GetElements returns one or more elements, then GetTopologies must return one or more topologies.

pub fn watch_topology( &self, ) -> QueryResponseFut<u64, DefaultFuchsiaResourceDialect>

Get the current topology via a hanging get. The driver will immediately reply to the first WatchTopology sent by each client. The driver will not respond to subsequent WatchTopology calls from that client until the signal-processing topology changes, which occurs as a result of a SetTopology call. The driver will close the protocol channel with an error of ZX_ERR_BAD_STATE, if this method is called again while there is already a pending WatchTopology for this client.

pub fn set_element_state( &self, processing_element_id: u64, state: &SettableElementState, ) -> QueryResponseFut<SignalProcessingSetElementStateResult, DefaultFuchsiaResourceDialect>

Controls a processing element using a unique ElementId returned by GetElements. Note that SettableElementState is a subset of ElementState, because some fields returned from WatchElementState (e.g. latency) can only be observed (not set) by the client.

Returns ZX_ERR_INVALID_ARGS if the processing_element_id does not match an id returned by GetElements or the type of SettableTypeSpecificElementState does not match the ElementType of the processing element returned by GetElements for this id. The driver may return ZX_ERR_INVALID_ARGS if the state values are invalid, i.e. any of the values violates rules specified in this protocol, e.g. trying to change an EQUALIZER processing element’s EqualizerBandState frequency when this processing element did not advertise CAN_CONTROL_FREQUENCY in its supported_controls.

SetElementState may be called before or after non-SignalProcessing protocol calls. If called after non-SignalProcessing protocol calls then SetElementState may or may not require renegotiation of the driver state as reached with calls of the protocol composing SignalProcessing, e.g. Dai. For instance, SetElementState changing an AGL processing element’s parameters may not require renegotiation of the Dai state because changing a gain parameter usually does not change the set of supported audio formats. By contrast, if SetElementState changes the parameters of a CONNECTION_POINT element, the change may require renegotiation because it may invalidate the set of supported formats returned in a previous GetDaiFormats Dai protocol call.

It is the driver’s job to determine when renegotiation is required. If renegotiation is required, then SetElementState must return ZX_ERR_BAD_STATE and the client must close the protocol channel such that the protocol negotiations are started over. The client then must make the SetElementState call that returned ZX_ERR_BAD_STATE before any non-SignalProcessing protocol calls.

pub fn set_topology( &self, topology_id: u64, ) -> QueryResponseFut<SignalProcessingSetTopologyResult, DefaultFuchsiaResourceDialect>

Sets the topology to be used using an id to the vector returned by GetTopologies. The current topology is communicated by WatchTopology responses. To change which topology is active, a client uses SetTopology. If the specified topology_id is not within thetopologies returned by GetTopologies, this call will return ZX_ERR_INVALID_ARGS. If GetTopologies returns only one Topology, SetTopology is optional and has no effect.

SetTopology may be called before or after non-SignalProcessing protocol calls. If called after non-SignalProcessing protocol calls, then SetTopology may return ZX_ERR_BAD_STATE to indicate that the operation can not proceed without renegotiation of the driver state. See SetElementState for further discussion.

Trait Implementations

impl Clone for SignalProcessingProxy

fn clone(&self) -> SignalProcessingProxy

Returns a copy of the value.

fn clone_from(&mut self, source: &Self)

Performs copy-assignment from source.

impl Debug for SignalProcessingProxy

fn fmt(&self, f: &mut Formatter<'_>) -> Result

Formats the value using the given formatter.

impl Proxy for SignalProcessingProxy

type Protocol = SignalProcessingMarker

The protocol which this Proxy controls.

fn from_channel(inner: AsyncChannel) -> Self

Create a proxy over the given channel.

fn into_channel(self) -> Result<AsyncChannel, Self>

Attempt to convert the proxy back into a channel.

fn as_channel(&self) -> &AsyncChannel

Get a reference to the proxy’s underlying channel.

fn into_client_end(self) -> Result<ClientEnd<Self::Protocol>, Self>

Attempt to convert the proxy back into a client end.

fn is_closed(&self) -> bool

Returns true if the proxy has received the PEER_CLOSED signal.

fn on_closed(&self) -> OnSignals<'_, Unowned<'_, Handle>>

Returns a future that completes when the proxy receives the PEER_CLOSED signal.

impl SignalProcessingProxyInterface for SignalProcessingProxy

type GetElementsResponseFut = QueryResponseFut<Result<Vec<Element>, i32>>

type WatchElementStateResponseFut = QueryResponseFut<ElementState>

type GetTopologiesResponseFut = QueryResponseFut<Result<Vec<Topology>, i32>>

type WatchTopologyResponseFut = QueryResponseFut<u64>

type SetElementStateResponseFut = QueryResponseFut<Result<(), i32>>

type SetTopologyResponseFut = QueryResponseFut<Result<(), i32>>

fn get_elements(&self) -> Self::GetElementsResponseFut

fn watch_element_state( &self, processing_element_id: u64, ) -> Self::WatchElementStateResponseFut

fn get_topologies(&self) -> Self::GetTopologiesResponseFut

fn watch_topology(&self) -> Self::WatchTopologyResponseFut

fn set_element_state( &self, processing_element_id: u64, state: &SettableElementState, ) -> Self::SetElementStateResponseFut

fn set_topology(&self, topology_id: u64) -> Self::SetTopologyResponseFut