class WireSyncBufferClientImpl

Returns a vector of supported processing elements.

This vector must include one or more processing elements.

Caller provides the backing storage for FIDL message via an argument to `.buffer()`.

Get the processing element state via a hanging get.

For a given `processing_element_id`, the driver will immediately reply to the first

`WatchElementState` sent by the client. The driver will not respond to subsequent client

`WatchElementState` calls for that `processing_element_id` until any portion of the

`ElementState` has changed from what was most recently reported for that element.

The driver will close the protocol channel with an error of `ZX_ERR_INVALID_ARGS`, if

`processing_element_id` does not match an ElementId returned by `GetElements`.

The driver will close the protocol channel with an error of `ZX_ERR_BAD_STATE`, if this

method is called again while there is already a pending `WatchElementState` for this client

and `processing_element_id`.

Caller provides the backing storage for FIDL message via an argument to `.buffer()`.

Returns a vector of supported topologies.

This vector must include one or more topologies.

If more than one topology is returned, then the client may select any topology from the

list by calling `SetTopology`.

If only one topology is returned, `SetTopology` can still be called but causes no change.

Each Element must be included in at least one Topology, but need not be included in every

Topology.

Caller provides the backing storage for FIDL message via an argument to `.buffer()`.

Get the current topology via a hanging get.

The driver will immediately reply to the first `WatchTopology` sent by each client.

The driver will not respond to subsequent `WatchTopology` calls from that client until the

signal processing topology changes; this occurs as a result of a `SetTopology` call.

The driver will close the protocol channel with an error of `ZX_ERR_BAD_STATE`, if this

method is called again while there is already a pending `WatchTopology` for this client.

Caller provides the backing storage for FIDL message via an argument to `.buffer()`.

Sets the currently active topology by specifying a `topology_id`, which matches to an entry

in the vector returned by `GetTopologies`.

The currently active topology is communicated by `WatchTopology` responses. To change which

topology is active, a client uses `SetTopology`.

If `GetTopologies` returns only one `Topology`, `SetTopology` is optional and has no effect.

This call will fail and return `ZX_ERR_INVALID_ARGS` if the specified `topology_id` is not

found within the`topologies` returned by `GetTopologies`.

`SetTopology` may be called before or after non-`SignalProcessing` protocol calls.

If called after non-`SignalProcessing` protocol calls, then `SetTopology` may return

`ZX_ERR_BAD_STATE` to indicate that the operation can not proceed without renegotiation of

the driver state. See `SetElementState` for further discussion.

Caller provides the backing storage for FIDL message via an argument to `.buffer()`.

Controls the processing element specified by `processing_element_id`, a unique ElementId

returned by `GetElements`.

The `state` specified in calls to `SetElementState` is a `SettableElementState`. This is a

subset of `ElementState` because some fields returned by `WatchElementState` (e.g. `latency`

or `plug_state`) can only be observed (not set) by the client.

Returns `ZX_ERR_INVALID_ARGS` if `processing_element_id` does not match a known ElementId

returned by `GetElements`, or if `state` is not valid for the element. This entails any

violation of the rules specified in this protocol.

Examples:

`state` specifies that an element should be stopped or bypassed, but the corresponding

element does not specify (or explicitly set to false) `can_stop` or `can_bypass`.

`state` includes a `type_specific` entry, but that `SettableTypeSpecificElementState` does

not match the `ElementType` of the element corresponding to `processing_element_id`.

`state` changes an `EqualizerBandState` for an `EQUALIZER` element (so far so good), but

specifies a change to `frequency` when this element did not set `CAN_CONTROL_FREQUENCY`

in its `supported_controls`.

`state` specifies a `GainElementState` for a `GAIN` element with a `gain` value that is

-infinity, NAN, or outside the Element's stated [`min_gain`, `max_gain`] range.

Callers may intersperse method calls to the `SignalProcessing` protocol with calls to other

driver protocols. Some non-`SignalProcessing` configuration changes may require a

renegotiation of the driver state before certain elements can receive a `SetElementState`.

For example, if a `DaiFormat` is changed, then `SetElementState` changing an `AGL` element's

parameters may not require renegotiation of driver state because changing gain parameters

usually does not change the set of supported audio formats.

By contrast, following the same `DaiFormat` change, before `SetElementState` can be called

on a `CONNECTION_POINT` element, the driver state may need to be reestablished because the

format change may invalidate the set of supported formats returned in a previous

`GetDaiFormats` protocol call for another part of the Topology.

It is the driver's job to determine when renegotiation is required. When this is needed,

the related `SetElementState` call must return `ZX_ERR_BAD_STATE` and the client must

close the protocol channel entirely, such that the protocol negotiations are started over.

The client then must re-invoke the `SetElementState` call that returned

`ZX_ERR_BAD_STATE` before any non-`SignalProcessing` protocol calls.

Caller provides the backing storage for FIDL message via an argument to `.buffer()`.

Create the ring buffer used to pass audio to/from this device. If the device is

Composite, then the targeted RING_BUFFER ENDPOINT must be identified by `element_id`.

Should only be called for Composite devices.

Caller provides the backing storage for FIDL message via an argument to `.buffer()`.

Set the wire format for the digital interconnect connected to this Codec endpoint.

This method returns information related to the format that was set, including delay values.

If the device is Composite, then the targeted DAI_INTERCONNECT ENDPOINT must be identified

by `element_id`.

Should only be called for Codec and Composite devices.

Caller provides the backing storage for FIDL message via an argument to `.buffer()`.

Start the Codec hardware. If successful, this returns after the Codec was started and

`start_time` indicates the time when the hardware started. Note that the Codec's DaiFormat

must be set (by a successful `SetDaiFormat` call) before calling this method.

Should only be called for Codec devices.

Caller provides the backing storage for FIDL message via an argument to `.buffer()`.

Stop the Codec hardware. If successful, this returns after the Codec was stopped and

`stop_time` indicates the time when the hardware stopped. Note that the Codec's DaiFormat

must be set (by a successful `SetDaiFormat` call) before calling this method.

Should only be called for Codec devices.

Caller provides the backing storage for FIDL message via an argument to `.buffer()`.

Reset the hardware -- stopping the hardware, releasing any ring buffers, and clearing any

DaiFormats or RingBufferFormats that were set.

This method returns when the hardware reset is complete.

After calling this method, the device is still controlled, but any ring buffers must be

re-created and re-started.

For devices with DAI_INTERCONNECTs (such as Codecs and some Composites), `SetDaiFormat` and

`CodecStart` must be called again (in that order) to return the interconnect to the active

operational mode.

As applicable, `SetTopology` and `SetElementState` must also be called.

Should only be called for Codec and Composite devices.

Caller provides the backing storage for FIDL message via an argument to `.buffer()`.